| About the Troubleshooting the Pocket NC category |   | 1 | 1095 | April 27, 2021 | 
        
          | How to cut the part from the stock in first part tutorial? |         | 8 | 1552 | September 14, 2025 | 
        
          | Measure tool length with setter button |   | 0 | 198 | July 31, 2025 | 
        
          | "Enclosure opened while program is running" error, however, I don't have an NC enclosure |   | 0 | 188 | July 3, 2025 | 
        
          | Enclosure reed switch |   | 0 | 161 | July 1, 2025 | 
        
          | Problems Configuring Fusion360 for my V2-10 |     | 3 | 290 | May 6, 2025 | 
        
          | Y axis getting stuck not moving when probing the tool length |           | 5 | 1123 | April 30, 2025 | 
        
          | Penta on vacation? |   | 0 | 267 | April 29, 2025 | 
        
          | Machine will not finish booting up |   | 0 | 224 | April 17, 2025 | 
        
          | Joint 4 following errors after software update 5.8.1 |     | 8 | 529 | March 24, 2025 | 
        
          | Fusion 360 “Center of Rotation” programming not working |     | 2 | 267 | March 24, 2025 | 
        
          | V5.8.2 tool wear |       | 6 | 440 | February 26, 2025 | 
        
          | Machine not working after upgrading from 5.5.12 to 5.8.1 |     | 10 | 552 | February 17, 2025 | 
        
          | Inaccuracy in Z-axis |       | 15 | 544 | January 26, 2025 | 
        
          | Minimizing Extended Toolholder Runout |     | 2 | 382 | January 23, 2025 | 
        
          | Simulator vs. Mouse |       | 16 | 865 | January 21, 2025 | 
        
          | Beginners Questions Pocket NC V2-10 Bought used |     | 1 | 586 | January 8, 2025 | 
        
          | Assistance Required for Penta Pocket V.2.50 Connection Issue |     | 3 | 328 | December 2, 2024 | 
        
          | Work Offset Issue |     | 6 | 431 | November 27, 2024 | 
        
          | A-Axis on V2-10 not perpendicular |     | 1 | 418 | October 21, 2024 | 
        
          | Machine pressure not changing |       | 3 | 453 | August 29, 2024 | 
        
          | Enclosure opened while program is running. program has been paused |     | 3 | 535 | August 29, 2024 | 
        
          | Disconnecting Mid Cut |     | 3 | 404 | August 28, 2024 | 
        
          | V2-50 Z Axis Stalling on Track |     | 1 | 450 | August 6, 2024 | 
        
          | Probe tripped during a non-probe move |       | 3 | 645 | August 5, 2024 | 
        
          | Squeaky nut on Y Axis |         | 6 | 890 | July 29, 2024 | 
        
          | Direct Ethernet Connnection |         | 9 | 1143 | July 10, 2024 | 
        
          | Built in simulator showing incorrect paths (reflected in real machine) |     | 1 | 496 | June 30, 2024 | 
        
          | Pendant Jogging in MM |   | 0 | 418 | June 28, 2024 | 
        
          | Tool Holder Collision Issues |     | 1 | 491 | June 28, 2024 |